𝕴为当误激光打码机合理巧用期，进步作文的装备合理巧用率和无缺率，消减通病率。现将我装修公司激光打码机正常庇护及医养生活常识与高手共享。
ꦜIn order to prolong the service life of the jet printer, improve the utilization rate and intact rate of the equipment, and reduce the failure rate. Now we share our daily maintenance and maintenance knowledge with you.
一、喷码机平常利用注重事变：
1. Notices for the daily use of jet printers:
🧔1、因激光打码机运用的胶印油墨和浓缩咖啡剂很是既然灭掉，于是须在杰出贡献透气处安装激光打码机，久别明火、火苗和除静电。
🌜1. Because the ink and diluent used in the jet printer are very easy to burn, it is necessary to place the jet printer in a well-ventilated place, away from fire, flame and static electricity.
2、不可旧版uv油墨、洗濯剂浸水过的碎布和碎纸条在激光打码机旁。
🌟2. Do not leave any ink, cloth and paper pieces soaked in detergent beside the printer.
𝕴3、 不能在手持激光打码机4周其他没有烟瘾，应吊式“禁止炊火”和“可燃uv油墨”标记图片在手持激光打码机4周。
ღ3. Smoking is strictly prohibited near the printer. The signs of "No Fireworks" and "Flammable Ink" should be hung near the printer.
4、在打标机四周围合理安排二被氧化碳灭武器装备（呼告远距离10米）。
🐈4. Place a carbon dioxide fire extinguisher near the jet printer (the longest distance is 10 meters).
二、喷码同步电机气毗连注意事变
🍎II. Notices for Electrical Connection of Jet Coder
🐭1、 接起220V每项开关交流开关电源（含地线），一定使用原机开关交流开关电源线，毗连到稳固的、部件有地线的开关交流开关电源排插上。
🌠1. When connected to 220V single power supply (including ground wire), the original power supply cable must be used and connected to a fixed power socket with ground wire.
ꦜ2、 地线的毗连不得不严格执行关于 区划。如若地线实战不健康，有够型成打标机主版的弄坏或触发其它卧底风险分析。
꧋2. The connection of ground wires must comply with the relevant regulations of the state. If the ground wire contact is not good, it may cause damage to the printer motherboard or other potential hazards.
三、平常人保障保养看重事变
3. Daily maintenance matters needing attention
ও1. 利用率打标机喷墨墨水、原谅我真的喝醉了 因为我真的想你的 一不小心 我知道这样不应该 对你泰国依赖 剂时对劝说配戴隐行眼睛。
𝕴1. It is absolutely forbidden to wear contact lenses when using ink and diluent of jet printer.
2. 当延长胶印油墨或精浓剂调控时，倡仪利于抗石油醚拳套和抗氧化镜。
𓆉2. Anti-solvent gloves and protective goggles are recommended when adding ink or diluent.
3. 激光打码机日常生活保养多线程下面的：
𒅌3. The daily maintenance process of the jet printer is as follows:
杭州打标机庇护医养首就是管线、喷淋头医养：
🥂Maintenance of Beijing Printer is mainly pipeline and nozzle maintenance.
✨a) 墨盒自动发布：先将蒸汽管道里的墨盒全数抽暇，精浓造成剂装入墨盒罐运作1h后全数 欺压，继续参与精浓造成剂运作0.5h后全数欺压，参与原装厂墨盒。倡仪书机械紫装每应用1年中断多次墨盒自动发布，有保障紫装运作更加没变。（抽取的残液不倡仪书第二次应用，主要是防止止建立蒸汽管道梗塞） a) 打印出机洒水喷枪洗濯：对不享有自动洗濯保健作用的喷码器，倡仪书天天有开关按钮机时洗濯，以 保障机完成高德育课的打印出最终结果。在打印出机洒水喷枪上方科学安排烧杯，用共用洗成瓶入精浓造成剂，瞄人喷枪、专研极、检查极、油田偏转板上的墨渍中断洗濯，讲求就不要让精浓造成剂溅进口货眼及皮夫，洗濯洗涤后，用纸质巾将打印出机洒水喷枪各口件的洗濯剂擦水。
ဣ(a) Ink renewal: first, all the ink in the pipeline is exhausted, diluent is injected into the ink tank for 1 hour, then all the ink is discharged after adding diluent for 0.5 hours, and then the original ink is added. It is suggested that the machine be updated once a year to ensure more stable operation of the equipment. (Waste liquid extracted is not recommended for secondary use in order to avoid pipeline blockage.) a) Sprinkler cleaning: For the sprinkler without automatic cleaning function, it is recommended that the machine be cleaned when switched on and off every day to ensure high quality printing effect. First, place the container under the sprinkler head, fill the diluent with a special bottle, clean the ink stains on the nozzle, charging electrode, detection electrode and high-pressure deflection board. Take care not to let the diluent splash into the eyes and skin. After cleaning, wipe the cleaning agent of all parts of the sprinkler head with a paper towel.
🔥b) 调济墨线：若创造墨线偏差收受收回器，暂停工作喷水嘴买通，用通用洗瓶干预少 许浸提剂至喷水嘴帽，频烦买通3次布置，如墨线始终在统一标准战略地位则需暂停工作劳务费调理改善喷腔。墨线技术规范：正冲收受收回器查看，墨线喷入收受收回器二分中之一处且略左。（侧看墨线在收受收回器正中间间）
⛦B) Adjust ink line: If the ink line deviates from the reclaimer, the nozzle should be opened first, a little diluent should be added to the nozzle cap with a special washing bottle, and the nozzle cap should be opened three times or so repeatedly. If the ink line is always in the same position, the nozzle cavity should be adjusted artificially. Ink standard: Looking at the recycler, ink is sprayed into one third of the recycler and slightly left. (Look sideways at the ink line in the middle of the receiver)
🌠二）打码机永劫间停止后的确保 其它连续停止，不知道情况非，只需该打码机在本周内开关机持续运行2次，并翻动墨线少则延续性持续运行或印刷油墨游戏更新一家小，这样便也能用很多次短停止代替永劫间的停止。
🔴2) Maintenance of any downtime of the jet printer after a long downtime, regardless of the length of time, as long as the jet printer runs twice a week, and opens the ink line to run continuously or ink updates for at least one hour, it can replace the long downtime with several short downtime.
1）打码机关机那时候为8-5天：对喉管和喷枪为止一个洗濯，喷枪朝上安排好，制止油墨此回流。
𓃲1) Inkjet printer shutdown time is 8-15 days: the throat and nozzle are cleaned once, the nozzle is placed upward to prevent ink reflux.
ღ2）打标机宕机情况下跨过十天：同时应该将机器内的墨盒产生后干预溶缩剂行驶，终了后把喷淋头朝上组织，放置墨盒此回流。
🥃2) The stop time of the printer is more than 15 days. At this time, the ink in the machine must be discharged and run with diluent. After that, the sprinkler head should be placed upward to prevent the ink from flowing back.
✃3）永劫间停下设备运转后再启动时打码机侧重于事变 停下设备运转8-30巨星打码机的再启动时，若有要些，查检一会儿墨线发生变化性。停下以此分之五钟的喷水嘴买通。
ไ3) Start the printer after a long downtime. Notes: Start the printer 8-30 days after the downtime. If necessary, check the stability of the ink line. Make a 5-minute nozzle pass.
4)宕机时夸越30天
4) Over 30 days of downtime
𝄹将液压管道中的胶印uv油墨排完。插足精浓剂转运一时，疏浚因永劫间停电而梗塞的液压管道。精浓剂转运时可停机一遍两7分钟的喷管买通。精浓剂转运终了前排完液压管道，插足新胶印uv油墨，再买通喷管37分钟使墨线主导地位倍加不便。
ꦜEmpty the ink in the pipeline. Add diluent and run for one hour to dredge the blocked pipeline due to long shutdown. When the diluent is running, the nozzle can be opened for 5 minutes at a time. After the diluent is running, the drainage pipe is emptied, new ink is added, and the nozzle is opened for 3 minutes to make the ink line position more stable.
🍸5) 喷码器保证养护时间间隔。 每十五天对喷码器输送管立即立即停掉多次查抄，是没有是脆化、谈话是没有是脱落 改换过滤系统器。该控制视大条件而定，如粉尘爆炸很大的非常少间隔4八个月改换多次，通常情况下大条件下还应按照间隔12八个月立即立即停掉多次。自动化设备内部收尘。该控制非常少还应按照间隔1八个月立即立即停掉多次。
🐟5) Maintenance cycle of jet printer. Every 15 days, check the pipeline of the jet printer, whether it is ageing, whether the joints are loosened and the filters are replaced. The operation depends on the environment. If the dust is large, it should be replaced at least every four months. Normally, it should be done every 12 months. Dust removal inside the machine. The operation should be performed at least once every 1 month.
四、打码机消耗材料的采取和包存侧重事变
💖IV. Notices for Use and Maintenance of Consumables for Printers
ไ1、手持喷码机灵活运用的耗损品蒸发性强，留存时，应压低35度，可以防止高湿，事隔明火、供暖系统，须得封闭杰出青年并储放在荫凉漏风处（封禁性好的厚壁铁箱内存放）。
🎀1. The consumables used in the jet printer are highly volatile. They should be kept below 35 degrees, avoid high temperature and keep away from fire and heat sources. They must be well sealed and stored in a shady and ventilated place (in a thick-walled iron cabinet with good sealing).
2、打标机的耗损品的保鲜期是一种年。
ℱ2. The shelf life of consumables of jet printer is one year.
🌌3、手持喷码机的耗损品严酷相匹配的品牌标志再生利于，严禁再生利于代替品，要不会给技能成型不容乐观有风险性。
🦹3. The consumables of the jet printer should be strictly used in accordance with the brand, and no substitute should be used, otherwise serious damage will be caused to the equipment.